CRP-Screen® Swiss Point of Care swiss point of care P-ST-CRP-54

CRP-Screen® Swiss Point of Care

SKU: P-ST-CRP-54
Sale price€14,95
Variant:
BabycheckCRP-ScreenFerri-CheckGluten-AlarmLiver-ScreenM-Albu-CheckMeno-CheckPoly-CheckProsta-CheckTik-Alert

Rapid self-test for the detection of C-reactive protein (bacterial infection or inflammation) in blood

The CRP-Screen® is a manual semi-quantitative immunochromatographic screening test for the assessment of C-Reactive Protein (CRP) level in finger prick whole blood sample. It can be used at home by lay users for self-testing for the detection of bacterial infections or inflammatory disorders

  • Screen Rapid self
  • test for detection of C
  • reactive protein (bacterial infection or inflammation) in blood.
  • Screen The C
  • Reactive Protein (CRP) is a non
Ready to ship within 24 hours!
Satisfaction guaranteed or your money back

CRP-Screen® Swiss Point of Care

The C-Reactive Protein (CRP) is a non-specific marker which is mainly produced by the liver and used to diagnose bacterial infectious disease and inflammatory disorders.

The CRP is a very sensitive and fast appearing indicator which could therefore be helpful for deciding an antibiotic treatment.

Depending on the CRP concentration, different lines will appear allowing the semi-quantitative interpretation of the test result.

In healthy patients, CRP concentration is lower than 8mg/L while the concentration level can go higher than 100mg/L in case of severe infection or during inflammatory process. Intermediate levels, within 8 and 100mg/L, are concomitant with more or less mildly viral or bacterial infections that can be easily overcome by appropriate treatment ordered by your doctor.

The CRP-Screen® is a manual semi-quantitative immunochromatographic screening test for the assessment of C-Reactive Protein (CRP) level in finger prick whole blood sample. It can be used at home by lay users for self-testing for the detection of bacterial infections or inflammatory disorders

How to use the CRP-Screen® Swiss Point of Care

Prepare everything properly before starting the testing procedure. Place the content of the box on a clean, dry and flat surface (e.g. table). Then perform the test as follows:

1.Wash your hands thoroughly. Use soap and warm water. Dry your hand with clean towel.

2. Prepare the test device and capillary pipette: Take them out from the protective pouch (tear at the notch) and place them in the reach of your hands (you will need them later). Discard the desiccant bag.

3. Open the diluent dropper vial: Remove the screw cap of the vial and keep it nearby.

4. Prepare the lancet. Hold the lancet without touching the trigger button. Unlock the cap twisting it off ¼ turn until you feel it separates from the lancet and then continue twisting it (2-3 rotations). Don’t pull just twist and discard the cap when finished. ①②

5. Clean the end of the middle or ring finger with cotton damped with alcohol. Massage the chosen finger towards the tip for 10 to 15 seconds to enhance the blood flow.

6. Prick the finger: put the lancet firmly against the side of the previously cleaned finger, and press the release trigger button.③ The lancet will automatically retract into the body of the device. Gently massage the finger to create a nice round blood droplet.④

7. Collect the blood with the capillary pipette: Gently touch the blood droplet with the open end of the capillary pipette. It must be filled until the line indicated on the capillary pipette. Do not press the bulb, it fills by itself. Make another blood droplet if the line is not reached. As far as possible, avoid air bubbles. ⑤

8. Place the collected blood sample into the previously opened diluent dropper vial by pressing the bulb of the pipette. Make sure that the complete volume of blood sample is added into the diluent dropper vial by pressing 2-3 times the bulb of the pipette and therefore rinsing the inner part of the pipette with diluent solution. Replace the screw cap on the diluent dropper vial and mix thoroughly. ⑥

9. Break the tip of the dropper vial containing the diluted blood sample. Hold it vertically and slowly add exactly 4 drops in the sample well of the device with an interval of 2-3 seconds between each drop. ⑦&⑧

10. Read the result after 5 minutes. Do not interpret after 10 minutes.

You may also like

Customer reviews

Our reviews are authentic. Only verified buyers receive an email invitation to review the items they purchased. We reserve the right to remove unlawful review content.